Condtrol Vector 30 - Bedienungsanleitung

MESSAGE CODES

While operation, the following codes/symbols may appear on the display:

Message

code

Problem

Solution

203

Battery is too low.

Replace the batteries.

402

Calculation error.

Make measurement again.

301

Temperature is too

high.

Cool down the device to

operating temperature range.

302

Temperature is too

low.

Warm up the device to

operating temperature range.

101

Reflected signal is too

weak.

Choose the surface with

stronger reflectance. Use the

reflecting plate.

102

Reflected signal is too

strong.

Choose the surface with weaker

reflectance. Use the reflecting

plate.

201

Ambient light is too

strong.

Make measurements in less

illuminated zone.

401

Hardware error.

Switch on/off the device

several times. If the symbol

still appears, then the device

may be defective. Contact the

store where the device was

purchased, or an authorized

service center.

CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires careful

handling. The following recommendations will extend the life of the

device:

- Do not point the device at the sun.

- Protect the device from bumps, falls, and excessive vibration; do not let

liquids, construction dust and foreign objects get inside the device.

- Do not expose the device to extreme temperatures.

- If liquids get inside the device first remove the batteries, then contact

the service center.

- Do not store or use the device under high humidity conditions for a long

time.

- Clean the device with soft wet cloth.

- Keep device optics clean and protect it from mechanical damage.

- Сarry out control measurements occasionally, especially if the device is

subject to excessive mechanical or other impact, before and after taking

important measurements.

Failure to observe the following rules may lead to leakage of electrolyte

from the batteries and damage of the device:

- Remove the batteries from the device if it is not used for a long time.

- Do not use batteries of different types, with different charge level.

- Do not leave discharged batteries in the device.

UTILIZATION

Expired tools, accessories and package should be passed for waste recycle.

Please send the device to the following address for proper recycle:

CONDTROL GmbH

Wasserburger Strasse 9

84427 Sankt Wolfgang

Germany

Do not throw the device in municipal waste!

According to European directive 2002/96/ЕC expired measuring tools

and their components must be collected separately and submitted to

environmentally friendly recycle of wastes.

WARRANTY

All CONDTROL GmbH devices go through post-production control and are

governed by the following warranty terms. The buyer’s right to claim about

defects and general provisions of the current legislation do not expire.

1) CONDTROL GmbH agrees to eliminate all defects in the device, discovered

during the warranty period, that represent the defect in material or

workmanship in full volume and at its own expense.

2) The warranty period is 24 months and starts from the date of purchase by

the end customer (see the original supporting document).

3) The warranty doesn’t cover defects resulting from wear and tear or

improper use, malfunction of the device caused by failure to observe the

instructions of this user manual, untimely maintenance and service and

insufficient care, the use of non-original accessories and spare parts.

Modifications in design of the device relieve the seller from responsibility for

warranty works. The warranty does not cover cosmetic damage, that doesn’t

hinder normal operation of the device.

4) CONDTROL GmbH reserves the right to decide on replacement or repair

of the device.

5) Other claims not mentioned above, are not covered by the warranty.

6) After holding warranty works by CONDTROL GmbH warranty period is not

renewed or extended.

7) CONDTROL GmbH is not liable for loss of profit or inconvenience associated

with a defect of the device, the rental cost of alternative equipment for the

period of repair.

This warranty applies to German law except provision of the United Nations

Convention on contracts for the international sale of goods (CISG).

In warranty case please return the device to retail seller or send it with defect

description to the following address:

CONDTROL GmbH

Wasserburger Strasse 9

84427 Sankt Wolfgang

Germany